Nebi Air Mask White Nebuliser

Nebi Air Mask is intended for inhalation therapy in healthcare facilities or for home medical care. The device can be used by adults, children and people with limited mobility under adult supervision.

Nebi Air Mask can be powered and charged with a Type-C cable, including while the device is in use. Use an approved DC 5.0 V 1.0 A power adapter compliant with IEC 60601-1, as the power adapter is not included. Disconnect the device from the power source after use.

First, attach the container to the main unit; a distinct click confirms that it is correctly fitted. Then attach the appropriate mask or mouthpiece. Before use, clean, disinfect and dry all parts thoroughly in accordance with the instructions.

A full battery charge takes approximately 2 hours. The indicator flashes while charging and turns solid green once charging is complete. When fully charged, the battery can power the device continuously for up to 60 minutes.

The indicator shows the operating and charging status, as well as situations that require the device to be checked. A solid blue light indicates operation, flashing green indicates charging, and a solid green light indicates a full charge. Five blue flashes signal a low battery level, three indicate that there is no liquid or that the device is not held upright, and ten indicate the end of the 10-minute operating time.

Before use, clean, disinfect and dry all Nebi Air Mask components. This prepares the device and accessories for the next use in accordance with the cleaning and disinfection instructions.

Open the lid, inject the solution into the container and close it securely before switching on the device. The recommended amount of liquid is 2–6 ml, and the container must not be filled above 6 ml. Hold the device upright during nebulisation so that the liquid remains in contact with the mesh disc.

Gently shake the device horizontally to mix the solution, put on the mask or place the mouthpiece in your mouth, and press the power button. Take slow, deep breaths while the solution is released. The device switches off automatically after 10 minutes; to continue, press the button again and check the amount of liquid. After use, switch off the device, remove the container and empty it.

For manual cleaning, use 0.5%–1% neodisher MediClean forte for 10–30 minutes at 30°C. Wearing disposable gloves, immerse the device, ensuring that no air bubbles remain, wipe the surfaces with a soft, lint-free cloth, and flush the internal channel of the device five times with detergent using a syringe. Then rinse under running water for 30 seconds, rinse in fresh deionised water for 5 minutes, and dry with a lint-free towel.

For manual disinfection, undiluted MetriCide™ OPA Plus can be used at room temperature by immersing the accessories for at least 5 minutes. Remove air bubbles from the surfaces using a sterile, soft cloth. After the required time, remove the parts, rinse them with sterile water, then wipe and dry them with a sterile cloth. Always check the disinfectant's instructions for use.

After cleaning, shake the container to remove any remaining water from it and the mesh disc. Leave the accessories to dry for at least 4 hours. Before use, check that all parts, especially the mesh disc and container, are completely dry.

After cleaning and disinfection, check that the device is clean and dry and has no dents, cracks, deformations or scratches. Also make sure that the markings remain clearly legible. Replace worn components, and do not use the device if it is damaged or shows changes in the material. Carry out testing and maintenance in accordance with the manufacturer's instructions.

First, inspect every component of the system and replace any parts with cracks or other damage. Pour 1–6 ml of 0.9% saline solution into the chamber, press the ready button and check that the indicator light is on and aerosol is visible. Press the button again to switch off the device and make sure the indicator light has gone out. Before the device is used by a patient, discard any remaining liquid.

Store the Nebi Air Mask at a temperature of -20°C to +55°C, at 10%–93% RH, non-condensing, and away from sunlight, high temperatures and moisture. After use, wash and disinfect the device and accessories, place them in the packaging and protect them from shocks. Replace the medicine container after no more than 18 months. If the device has been outside this temperature range, leave it at room temperature for 2 hours.

Nebi Air Mask is intended for inhalation therapy in healthcare facilities or for home medical care. The device can be used by adults, children and people with limited mobility under adult supervision.