Bella Set Grey Concrete Baby rocker

Keep batteries out of children's reach, insert them according to the marked polarity and never throw them into a fire. Do not mix different types of batteries or new and used batteries, short-circuit the terminals or charge batteries that are not designed for charging. If the product will not be used for an extended period, remove the batteries and dispose of depleted batteries immediately; this also applies to the button batteries in the remote control.

Connect the USB cable to the power adapter, plug the power adapter into a socket and insert the other end of the cable into the DC port in the bouncer base. Use only a power adapter rated at 5.8 V DC, 0.8 A. Regularly check the condition of the cable, plug, contacts and other power adapter components; if you notice any damage, stop using it.

First, loosen the screw with a screwdriver and remove the battery compartment cover. Insert the batteries according to the polarity, replace the cover and tighten the screw. When closed in this way, the compartment helps keep the batteries in place while the device is in use.

To assemble it, place the bouncer supports on the base; a click from the release buttons confirms that they are correctly positioned. Connect the front and rear frame sections by matching the tubes marked with the same letter, and place the metal tabs in the corresponding holes. Fit the cover over the frame and fully fasten the zip—do not use the bouncer if the zip is not fully closed. To remove the bouncer from the base, press the release buttons on both sides of the mounting element.

Adjust the harness to your child's height by threading it through the appropriate openings in the cover, then insert it into the buckles at the back of the seat and tighten it. After placing your child in the bouncer, fasten the snap elements in the buckle and the cover's hook-and-loop fasteners. A click confirms that it is fastened correctly; do not use the bouncer if the harness is not fastened correctly. To unfasten the harness, press the button on the buckle.

Insert the toy bar into the mounting element on the bouncer frame until you hear a click confirming that it is securely attached. The toy bar can be set in one of five positions. To remove it, simply press the release button. Do not carry the product by the toy bar.

You can rotate the bouncer 360° and set it to face the direction you choose. To change the seat position, press the adjustment buttons on both sides of the frame and select the upright, reclined or semi-reclined position. Connect the device to a power supply or insert the batteries, then press the power button on the control panel or remote control. Finally, select one of the five rocking speeds.

You can choose from six rocking modes and select one according to your current needs. In automatic mode, the rocking pattern changes approximately every 16 seconds. When night mode is selected on the control panel or remote control, the rocking gradually slows down until it stops completely.

When the Bella Set detects the child's movement, it automatically switches on the rocking motion and melody. You can activate this function using the button on the control panel or remote control. To switch it off, press the same button again.

Press the melody selection button on the control panel to start playback. Press the button again to switch it off. Press and hold the button to increase or decrease the volume. Using the remote control, you can start playback, select the next or previous melody and adjust the volume with the corresponding buttons.

Place the bassinet support bracket on the base; a click from the release buttons confirms that it is correctly attached. Join both parts of the bassinet support and check that the metal tabs are positioned in the correct holes. Begin attaching the bassinet to the bracket from the part with the cover fitted, connect the tubes marked with the same letter and place the support in the plastic guides on the outside of the bassinet base. To remove the bassinet from the base, press the release buttons on both sides of the mounting element.

Attach the toy bar by placing it on both sides of the bassinet frame. Make sure that both sides of the toy bar are securely seated on the frame. This positions the toys above the bassinet as intended.

If the device shakes excessively, first check that it has been correctly attached to the base. Make sure the component has been installed according to the instructions before using it again.

Keep batteries out of children's reach, insert them according to the marked polarity and never throw them into a fire. Do not mix different types of batteries or new and used batteries, short-circuit the terminals or charge batteries that are not designed for charging. If the product will not be used for an extended period, remove the batteries and dispose of depleted batteries immediately; this also applies to the button batteries in the remote control.