Fidi Free Simple White Natural Breast pump

The massage mode on the Fidi Free Simple breast pump has 9 intensity levels. It simulates the initial sucking phase during breastfeeding, so you can choose the level that feels most comfortable for you.

The expression mode on the Fidi Free Simple breast pump offers 9 intensity levels. It simulates the deeper sucking phase during breastfeeding, and the setting should remain comfortable.

Before assembly, wash your hands, then wash, sanitise and completely dry the parts that come into contact with milk. Place the silicone membrane on the T-piece and check that its rim is correctly attached. Then insert the suction valve into the lower opening of the T-piece. Place the T-piece in the milk container, positioning the wings inside the tabs on the back wall, and press it into the opening for the main body. Attach the silicone funnel and align its deflector with the milk overflow opening. If necessary, use the 15, 17, 19 or 21 mm insert. Finally, connect the main body to the container and check that everything is assembled correctly.

The nipple should be positioned centrally in the tunnel of a well-fitted funnel. Place the Fidi Free Simple breast pump inside a standard nursing bra and make sure there is no gap between your breast and the silicone funnel. Use the device while sitting or standing, without leaning forward or changing its position during operation. If you are wearing a firm bra, unfasten the strap, attach the included fastener and adjust its length. If expressing causes discomfort or pain, stop using the device immediately.

Before your first session, charge the Fidi Free Simple breast pump for 2 hours, wash your hands, and check the assembly and fit. Press and hold the power button to start the device. It will begin operating in the mode used during the previous session. Use the mode button to switch modes and the pause/start button to pause or resume operation. Use the decrease and increase buttons to set the intensity from 1 to 9, avoiding any level that causes pain. Increase the intensity until you feel slight discomfort, then reduce it by one level. Briefly press the power button to switch off the device. It will also switch off automatically after 30 minutes of continuous operation.

While the breast pump is running, lean forward slightly so that the milk flows from the tunnel into the container, then switch off the Fidi Free Simple breast pump. Remove the device from your bra and disconnect the main body. Tilt the container with the rounded part facing down, then pour the milk through the opening into a bottle or storage container. Do not store milk in the device or refrigerate it together with the device.

Expressed milk can be stored at a temperature of 16–25°C for up to 4 hours, or for up to 6 hours under very clean expressing conditions. In a refrigerator at a temperature of 4°C, it can be stored for up to 3 days, or for up to 5 days under very clean expressing conditions. In a freezer at a temperature of -18°C, milk can be stored for up to 6 months, or for up to 9 months under very clean conditions. Do not store it in the refrigerator door.

Defrost milk in the refrigerator for up to 24 hours, at room temperature for up to 2 hours, or under warm running water at a maximum temperature of 37°C. Use milk defrosted under running water immediately. Before feeding, gently shake the container and check the temperature. For freezing, use plastic bottles intended for contact with food or milk storage bags, filled to ¾ of their capacity. Do not defrost milk in a microwave or in boiling water. Do not refreeze defrosted milk or store it again at room temperature or in the refrigerator.

Connect the USB-C cable to the power socket on the side of the main body, and connect the other end to a 5V DC 1A USB adapter, which is not included. A flashing battery indicator means that the breast pump is charging. When it stops flashing, the Fidi Free Simple breast pump is fully charged. Before first use, charge the device for 2 hours. To help support battery life, charge it before it is completely depleted and fully charge it before storing it for a longer period.

First, remove the main body of the Fidi Free Simple breast pump. Then open the milk container from underneath by pulling on the silicone funnel. As you pull the funnel, remove the assembled T-piece from the container. Finally, separate the silicone funnel, silicone membrane and suction valve from the T-piece.

Wash the parts of the Fidi Free Simple breast pump that come into contact with the body and milk separately immediately after use. Do not clean or disinfect the main unit or power cord. Do not wash any part of the device in a dishwasher.

Before first use, wash the parts that come into contact with milk using a cleaning agent. Then sterilise the milk container, Y-piece, valve, membrane and breast shields in boiling water. Do not sterilise the main unit of the Fidi Free Simple breast pump.

After each use, remove the main unit of the Fidi Free Simple breast pump and clean it with a dry, soft cloth. Disassemble the device, rinse the parts that come into contact with the body and milk in cool water, then wash them in warm water with a mild detergent. Rinse the parts thoroughly under clean running water and disinfect them in boiling water for at least 10 minutes, ensuring they do not touch the bottom of the container. Leave the parts to dry on a clean towel, then store them in a clean bag, container or other clean place. Do not seal wet parts in an airtight container. Rinse the suction valve with clean water without inserting your fingers or any objects into it.

Connect the Fidi Free Simple breast pump to the adapter, as the battery may have discharged or entered protection mode after being stored for a long time. Once connected, the battery should activate. Fully charge the device before first use and after long-term storage.

The massage mode on the Fidi Free Simple breast pump has 9 intensity levels. It simulates the initial sucking phase during breastfeeding, so you can choose the level that feels most comfortable for you.