BABYPRESTO White Natural Water dispenser

Place the device on a flat, stable surface. Open the lid and pour in tap or filtered water, not exceeding 2000 ml, so that the water level is above the minimum indicator. Close the lid, then place the tank on the base.

Before first use, boil water in the BABYPRESTO water dispenser and then pour it away. The device is ready for further use only after this has been done.

First, make sure the water level is above the minimum indicator. Then connect the device to the power supply and switch it on using the on/off button. Press and hold the dispensing lock button until you hear a single audible signal and the tap's LED light comes on. Place the bottle on the base and touch the dispensing button. After 3 seconds, the default 30 ml will begin dispensing. Use the decrease and increase buttons to set a volume from 30-300 ml. After 10 seconds of inactivity, the dispensing lock will activate automatically.

In standby mode, touch the on/off button, then touch the function button once. When 35°C is reached, the device will emit a triple audible signal and switch to maintaining the set temperature.

In standby mode, switch on the device using the on/off button, then touch the function button twice. When the water reaches 55°C, you will hear a triple audible signal. The BABYPRESTO water dispenser will then switch to temperature-maintaining mode.

To select 70°C, touch the on/off button in standby mode, then touch the function button three times. Once the water has heated to the selected temperature, the device will confirm this with a triple audible signal. It will then switch to maintaining the temperature.

In standby mode, switch on the device using the on/off button, then touch the function button four times. The water boiling process will be confirmed by a triple audible signal. Once the water has cooled, the BABYPRESTO water dispenser will switch to maintaining a temperature of 45°C.

Switch the device on from standby mode using the on/off button, then touch the function button five times. The function will boil the water for 15 minutes, and completion will be confirmed by a triple audible signal. Once the water has cooled, the BABYPRESTO water dispenser will start maintaining a temperature of 45°C.

You can change the temperature using the buttons to decrease or increase the value, in increments of 5°C, within a range of 35-95°C. The set temperature display shows the target temperature, while the current water temperature display shows its present value. You can check the selected function on the function display.

The BABYPRESTO water dispenser maintains the temperature for 24 hours. Once the temperature selected in heating mode is reached, the device automatically switches to temperature maintenance mode.

After use, unplug the device and wait for it to cool down. Empty the water, then wipe the housing and the inside of the heater with a soft, damp cloth. Finally, dry the surfaces with a clean cloth or paper towel.

Descale the device regularly every 2–4 weeks, depending on the hardness of the water. Pour in 100 ml of white vinegar and 200 ml of cold water, boil the solution, then leave it in the device for 10 minutes. Set the dispensing amount to 270 ml so that the solution flows through the dispensing system. Then unplug the device, wait for it to cool down and empty the liquid. Rinse the device twice with fresh water. Finally, pour in 1000 ml of clean water, set the dispensing amount to 250 ml and dispense it twice more.

Error E1 means that the device cannot detect the water container. If the tank is removed from the base during operation, the power supply is automatically switched off. If you place the container back in the base within 10 minutes, the previous operating state will be restored.

Error E3 indicates that there is no water in the container. Add water until the level is above the minimum indicator, as the power supply is automatically switched off when this error occurs. The device will resume operation once it has cooled down naturally, while adding water may speed up the cooling process.

Place the device on a flat, stable surface. Open the lid and pour in tap or filtered water, not exceeding 2000 ml, so that the water level is above the minimum indicator. Close the lid, then place the tank on the base.